聯系方式
服務熱線：0531-85980985
聯系人： 寧經理 手機：13953116782 電話：15990999232 郵箱：499589624@qq.com 地址：濟南市槐蔭區清河北路11號（美里新居南門斜對面）亞德森工廠店
縫制工作服時要注意什么？
來源：http://www.tbjrw.cn 日期：2021-10-25 發布人：
職業裝（工作服）反映了時代潮流，成為人們注視的焦點。那么如何縫制職業裝才能使制服更具風采、更顯魅力呢?應該減輕面料車縫時縫縮起皺現象。職業裝面料本身對車縫狀況有很大的影響。比如一些組織細密的職業裝面料、經過后整理的面料、較薄且不具伸縮性的職業裝面料。
Business wear (work clothes) reflects the trend of the times and has become the focus of attention. So how to sew professional clothes to make uniforms more elegant and attractive? First of all, we should reduce the shrinkage and wrinkling of fabric during sewing. The fabric of professional wear itself has a great impact on the sewing condition. For example, some carefully organized professional wear fabrics, after finishing fabrics, thinner and non stretchable professional wear fabrics.
當縫紉的方向與這些職業裝面料的經向方向平行時，嵌入的縫線會將經紗迫離原位，因每針縫線都將經紗推開，經過多針積累所產生的偏差將沿著接縫的布身收縮從而導致車縫起皺，當縫紉的方向與這些職業裝面料的緯向方向平行時，通常較少起皺。而根據經驗顯示，在對角中斜向的接縫則不會起皺，大多數職業裝面料，只要使接縫處于經度或緯度的斜角15度方向，就足以避免起皺。因此，可考慮使用斜裁方式作業。必要時，可在職業裝面料上涂抹平滑劑。
When the sewing direction is parallel to the warp direction of these professional wear fabrics, the embedded suture will force the warp away from the original position. Because each sewing thread pushes the warp away, the deviation caused by multi needle accumulation will shrink along the cloth body of the seam, resulting in sewing wrinkling. When the sewing direction is parallel to the weft direction of these professional wear fabrics, there is usually less wrinkling. According to experience, the diagonal seam will not wrinkle. For most professional fabrics, it is enough to avoid wrinkle as long as the seam is in the direction of 15 degrees of longitude or latitude. Therefore, oblique cutting can be considered. If necessary, apply smoothing agent on the fabric of professional wear.
此外，應盡可能地使用細針。
In addition, fine needles should be used as much as possible.
因細針能明顯減少在穿過職業裝面料時所產生的阻力，故有防止縫縮起皺的效果，同時要注意經常更換新針。-東莞服裝廠
Because the fine needle can significantly reduce the resistance when passing through the professional clothing fabric, it has the effect of preventing seam shrinkage and wrinkling. At the same time, pay attention to replacing the new needle frequently- Dongguan garment factory
當使用合成縫紉線時，必須小心確定縫線的張力，應使張力調整到。底線張力必須調整到：當縫線自由移動的末端拉起時，底線梭心軸及外套慢慢向下滑動，面線與底線的張力必須保持一致，使它們恰好在兩層職業裝面料之間交織。合成縫紉線縫入職業裝面料的張力太大，將會自動收縮以緩和這種張力，這種現象將使沿著接縫的布身收縮，進而使接縫起皺。
When using synthetic sewing thread, the tension of the suture must be carefully determined and adjusted to the minimum. The tension of the bobbin thread must be adjusted to: when the end of the free movement of the suture is pulled up, the bobbin spindle of the bobbin thread and the jacket slide down slowly, and the tension between the upper thread and the bobbin thread must be consistent, so that they are just interwoven between the two layers of professional wear fabrics. If the tension of synthetic sewing thread sewed into professional clothing fabric is too large, it will automatically shrink to alleviate this tension. This phenomenon will shrink the cloth body along the seam and wrinkle the seam.
還要注意的是因上層職業裝(工作服)面料與壓腳之間的摩擦力，也會迫使送布牙上的下層職業裝面料移動更為迅速而導致接縫起皺。只要將壓腳的壓力盡量調低些，同時使用細牙的送布牙(輸送器)，降低縫紉機的回轉速度就可以避免送料產生的起皺，而完全解決這種問題的根本方法是采用具有差動送料或針送料機構的縫紉機。如何減輕面料車縫時縫縮起皺現象，職業裝面料本身對車縫狀況有很大的影響。比如一些組織細密的職業裝面料、經過后整理的面料、較薄且不具伸縮性的職業裝面料
It should also be noted that the friction between the upper professional wear (work clothes) fabric and the presser foot will also force the lower professional wear fabric on the cloth feeding teeth to move more quickly, resulting in seam wrinkling. As long as the pressure of the presser foot is reduced as much as possible and the fine tooth feed tooth (conveyor) is used at the same time to reduce the rotation speed of the sewing machine, the wrinkling caused by feeding can be avoided. The fundamental way to completely solve this problem is to use the sewing machine with differential feeding or needle feeding mechanism. How to reduce the shrinkage and wrinkling of fabric during sewing, the fabric of professional wear itself has a great impact on the sewing condition. For example, some carefully organized professional wear fabrics, after finishing fabrics, thinner and non stretchable professional wear fabrics
以上就是濟南服裝廠http://www.tbjrw.cn為大家介紹的內容，感謝您在百忙之中查看我公司的信息內容，如果您想要了解的更多，歡迎您來電進行咨詢!
The above is Jinan garment factory http://www.tbjrw.cn Thank you for checking the information of our company in your busy schedule. If you want to know more, you are welcome to call for consultation!
上一條：企業工裝采購必備哪些知識？ | 下一條：維修行業的工作服定做要注意哪些？
資訊MORE+
- 工作服跟工作服之間有什么區別呢？ 2025-04-19
- 濟南工作服：要對員工工作服都有什么要求？ 2025-04-18
- 濟南工作服定制的舒服度 2025-04-15
- 濟南工作服弄上油漆怎么快速洗干凈？ 2025-04-14
- 為什么要穿職業裝 2025-04-12
- 工作服廠家的特點及流程 2025-04-11
- 工裝的衡量標準是什么？ 2025-04-10
- 員工形象才是行走的企業名片 2025-04-09
- 濟南服裝廠：工作服的實用建議 2025-04-08
- 濟南職業裝根據行業需求設計制作 2025-04-07
- 工作服要怎么選便宜舒服？ 2025-04-02
- 濟南職業裝傳統與現代碰撞出怎么樣的火花 2025-03-31
- 濟南工作服多元化 2025-03-28
- 用濟南工裝定做打造專屬企業形象 2025-03-24
- 濟南工裝定做怎么樣？ 2025-03-24
- 濟南工裝定做選擇方式你知道嗎? 2025-03-21
- 濟南工裝定做：定制工裝，彰顯企業風采 2025-03-20
- 時尚征程的者?濟南服裝廠 2025-03-18
- 濟南職業裝怎么做到職場形象的塑造的？ 2025-03-18
- 聽說濟南工作服是城市職場的實用風尚，到底為什么？ 2025-03-17
